Nissan data scan 2 cannot connect to bcm 2004 maxiam

#Nissan data scan 2 cannot connect to bcm 2004 maxiam serial
#Nissan data scan 2 cannot connect to bcm 2004 maxiam software
#Nissan data scan 2 cannot connect to bcm 2004 maxiam trial

Knowing this, if we focus on the last few lines in the EEPROM dump, youРІР‚в„ўll notice the characters 33 85 CC 7A repeated 8 times. The major value is what IРІР‚в„ўll be focusing on, since that controls the thousands of kilometers which is more important. Trip A and B are also stored in the EEPROM. The odometer has a major value in addition to a minor value that increments.

#Nissan data scan 2 cannot connect to bcm 2004 maxiam trial

Through a lot of trial and error, back and forth in the vehicle, and a few hours of hair pulling, calculating and note-taking, I was able to come up with a rough idea of how the odometer program works. Or if the engineer inside you is itching to make sense of 256 HEX characters, you can attempt to decode it. The additional advantage is I could now quickly disconnect and reconnect my chip to the odometer board, and then test my new program out on the car as I decoded the odometer program.Р”Р„t this point you can merely save the odometer dump, and write it to your new cluster. So I soldered wires to the РІР‚СљnewРІР‚Сњ chip, and was able to connect it to the programmer directly, without having the board hamper the write function. The 93C56 chip is identical electronically to the L56 chip. I found another replacement chip, the Microwire 93C56 chip from a carРІР‚в„ўs ECU I had laying around. Luckily, I had saved the EEPROM information I downloaded earlier. This is why you should use a hot air station so it heats all the pads evenly and you can just pick the chip off the board instead of prying it. So off we went trying to desolder an SMD chipРІР‚В¦Р”Р„nd SNAP!!! The leads broke off the chip. The EEPROM must be removed from the board if you want to write to it, as it canРІР‚в„ўt be programmed in circuit. Using the PonyProg software, I was able to read and save the information from the odometer chip. ThatРІР‚в„ўs it!Р”Р„nd hereРІР‚в„ўs my programmer connected to the PC.Р”Р„nd the breadboard with the resistors and diodes. The rest is some 22 AWG hookup wire and a breadboard ($5). All it is are three 5V zener diodes ($1) and three 4.7K ohm resistors ($1).

#Nissan data scan 2 cannot connect to bcm 2004 maxiam serial

It interfaces through the RS232 serial port. This is the EEPROM programmer I built to connect the chip to my desktop computer. Here's the original instrument cluster from my LX sedan, 314,622 km, and hereРІР‚в„ўs my new cluster.

A spare instrument cluster in case you screw up.

#Nissan data scan 2 cannot connect to bcm 2004 maxiam software

Serial programming software (PonyProg freeware).Computer with Windows XP and serial port.Soldering iron, solder and a de-soldering pump.You can also opt to merely swap the chips, or copy and paste the program, rather than decode.'' What follows is a hack-around to using HDS, by programming the mileage directly to the chip. The odometer information can be copied over from the old cluster to the new cluster using Honda HDS, assuming the original cluster is operable. The information is coded in HEX characters. The chip can be read and written to using a serial programmer. Odometer information is stored on a small EEPROM chip on the circuit board. Therefore the mileage of the original vehicle that the cluster was from will be displayed on the dash. The mileage on most (Japanese) cars is stored on the instrument cluster itself, and not in the ECU. LetРІР‚в„ўs say you swapped an instrument cluster from a coupe to a sedan to change the look or color of the needles, or youРІР‚в„ўre replacing a defective cluster.